NetApp NS0-014 問題練習

Question No : 1
What is a key benefit of transitioning from FC MetroCluster to IP MetroCluster?

• A.Improved storage capacity
• B.Reduced hardware costs and longer distance support
• C.Faster data replication
• D.Less frequent software updates

答えを確認する

正解:

Question No : 2
What is a key advantage of IP MetroCluster over Fibre Channel MetroCluster?

• A.Lower bandwidth requirements
• B.Easier setup and longer distance replication
• C.Higher performance
• D.Increased storage capacity

答えを確認する

正解:

Question No : 3
Which task is essential when expanding a MetroCluster system to support additional storage nodes?

• A.Disable all replication processes
• B.Add new storage shelves and validate SyncMirror configuration
• C.Remove ATTO FibreBridges
• D.Reinstall all controllers

答えを確認する

正解:

Question No : 4
Which technology allows MetroCluster to provide zero data loss failover?

• A.SnapVault
• B.SyncMirror
• C.ONTAP Mediator
• D.Snapshot

答えを確認する

正解:

Question No : 5
Which protocol is primarily used for data replication between MetroCluster sites in an IP-based configuration?

• A.Fibre Channel
• B.FCoE
• C.IP
• D.iSCSI

答えを確認する

正解:

Question No : 6
Which task must be completed first when upgrading MetroCluster hardware components?

• A.Update the ONTAP software
• B.Validate system compatibility using IMT
• C.Install new ATTO FibreBridges
• D.Install the Mediator software

答えを確認する

正解:

Question No : 7
Which tool is used to verify a customer environment’s compatibility with MetroCluster before deployment?

• A.OnCommand Workflow Automation
• B.Config Advisor
• C.System Manager
• D.SnapCenter

答えを確認する

正解:

Question No : 8
When planning for MetroCluster installation, which factor is essential to ensure smooth data recovery in case of a site failure?

• A.Site power supply
• B.Data replication speed
• C.WAN redundancy and low latency
• D.Network segmentation

答えを確認する

正解:

Question No : 9
Which MetroCluster component requires reconfiguration when upgrading from a 2-node to a 4-node configuration?

• A.SyncMirror
• B.ATTO FibreBridge
• C.Mediator
• D.FC switches

答えを確認する

正解:

Question No : 10
When configuring IP switches in a MetroCluster setup, which two tasks must be performed to validate the configuration? (Choose two)

• A.Check port channels
• B.Verify SnapMirror relationships
• C.Ensure VLAN tagging is properly set
• D.Confirm Mediator IP reachability

答えを確認する

正解:

Question No : 11
What is the role of Tiebreaker in MetroCluster configuration?

• A.Managing ATTO bridges
• B.Facilitating automatic switchover in case of WAN failure
• C.Monitoring Fibre Channel health
• D.Ensuring IP compatibility

答えを確認する

正解:

Question No : 12
What are the major requirements for planning an IP-based MetroCluster deployment? (Select two)

• A.ATTO bridges
• B.High-capacity Ethernet links
• C.Fibre Channel connectivity
• D.Support for IP routing

答えを確認する

正解:

Question No : 13
Which two components are required when setting up an IP-based MetroCluster configuration? (Select two)

• A.ATTO FibreBridge
• B.IP switches with proper redundancy
• C.SnapMirror software
• D.ONTAP Mediator

答えを確認する

正解:

Question No : 14
What is the primary purpose of the MetroCluster Tiebreaker in disaster recovery testing?

• A.To automatically upgrade ONTAP
• B.To manage automatic failover between sites
• C.To verify that storage shelves are properly synchronized
• D.To perform data deduplication

答えを確認する

正解:

Question No : 15
What are two requirements when transitioning from FC MetroCluster to IP MetroCluster? (Select two)

• A.Replace FC switches with IP switches
• B.Remove ATTO FibreBridges
• C.Maintain existing FC paths
• D.Upgrade to a compatible ONTAP version

答えを確認する

正解: