Senior Internal Corrosion Technologist 試験問題と解答 - 模擬練習 - 練習問題・模擬試験

Question No : 1
Thermal Spray coatings provide:

A.Barrier protection
B.inhibitive protection
C.Sacrificial protection
D.Thermal protection

正解:

Question No : 2
The best choice of Instrument for holiday testing of thick film concrete coatings is:

A.Low Voltage Sponge Type
B.High Voltage DC Pulse Type
C.High Voltage DC Constant Current
D.High Voltage AC

正解:

Question No : 3
The most likely area of failure on a buried external pipeline coating is the:

A.Mainline coating
B.Field Joint coating
C.Areas exposed to Ultra Violet light
D.Ground bed

正解:

Question No : 4
When measuring the Dry Film Thickness of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument Is the:

A.Ultra Sonic DFT Gauge
B.Tooke Gauge
C.Eddy Current Gauge
D.Magnetic Gauge

正解:

Question No : 5
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:

A.Magnetic coatings applied to a magnetic metallic substrate
B.Non-Conductive coatings applied to a conductive metallic substrate
C.Conductive coatings applied to a magnetic metallic substrate
D.Conductive coatings applied to a cementitious substrate

正解:

Question No : 6
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:

A.It contains biocide
B.It doesn’t contain biocide
C.The floating structure is stationary
D.It will result in a very slippery surface

正解:

Question No : 7
External coatings applied to burled pipelines are generally tested for:

A.Gloss level
B.Chalking resistance
C.Cathodic disbondment
D.Solvent resistance

正解:

Question No : 8
When performing a hardness test on a coating which has elastic properties the inspector is likely to observe:

A.A very high reading
B.A very low reading
C.Cold (low or creep
D.No difference from any other coating

正解:

Question No : 9
A single component water borne acrylic coating cures by:

A.Solvent Evaporation
B.Coalescence
C.Co-Reaction
D.Oxidation

正解:

Question No : 10
Surface preparation methods for Non-ferrous metals are:

A.The same as for Ferrous metals
B.The same for all Non-Ferrous metals
C.Specific for each type of Non-Ferrous metal
D.Not required

正解:

Question No : 11
The Concrete Repair Institute's comparators can be used to assess:

A.Surface cleanliness prior to coating
B.Surface profile prior to coating
C.Contamination levels prior to coating
D.Compressive and tensile strength prior to coating

正解:

Question No : 12
Differences in technique for abrasive blasting concrete versus steel require the operator to:

A.Lower the blast pressure
B.Move the nozzle quicker
C.Increase the standoff distance
D.a), b) and c)

正解:

Question No : 13
NACE No. 13 / SSPC 6 Identifies the use of:

A.Abrasive blasting only
B.Watterjetting only
C.Steam cleaning only
D.Various methods of cleaning

正解:

Question No : 14
Surface preparation of concrete is performed using:

A.Methods that are exactly the same as steel
B.Methods that are completely different to steel
C.Methods that have been modified for concrete
D.Methods that are the same as wood

正解:

Question No : 15
You are a NACE Level 2 in-house inspector working in a shop. Your In-house UP requires you to perform a sleeve test to test for soluble sails; however the 3rd party NACE Level 3 inspector, representing the owner, has used a salt smart meter and has achieved a very different result and has rejected the pre cleaning.
Your FIRST preferred course of action is to:

A.Advise the other Inspector he is using an Incorrect method
B.Redo the pre-cleaning based on the other Inspectors results
C.Review the specification with the other inspector to see what method was specified
D.Advise your QC Manager to change the UP to the use of the salt smart meter

正解:

AMPP Senior Internal Corrosion Technologist 問題練習